Whether it's motor oil, car batteries, brakes, or headlights for quick easy DIY jobs, or a more complex project like replacing your vehicle's head gasket or exhaust pipes, you'll find everything you need right here at Pep Boys. Quickly and easily search for the parts you need based on the year, make, and model of your vehicle. Pep Boys carries the OEM and aftermarket parts and accessories you need to repair, maintain, or customize your vehicle. We know there's more to driving than keeping your vehicle running. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury.Price Match PolicyThe purpose of the Pep Boys Price Match Policy is to ensure that we are the automotive solutions provider of choice for the value-oriented customer, putting the customer first by offering the best value available.įor retail: We will match any local competitor's advertised or every-day price, on any comparable merchandise normally stocked as active in our stores' inventory or outside purchase, within 30 days of purchase with the original receipt.įor tires: We will match any local competitor's advertised or every-day price, on comparable tires within 90 days of purchase with the original receipt.įor service: We will match a local competitor's advertised or every-day price, on comparable automotive services utilizing comparable merchandise.Ĭar & Truck Replacement PartsPep Boys carries the parts you need to keep your car or truck running for years to come. This is the only sure way to disable the airbag system. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. On vehicles equipped with airbags, disable the airbag system before attempting any steering wheel, steering column, seat belt tensioner, or instrument panel component diagnosis or service. Remove the cluster bezel from the instrument panel. Pull the left side of the cluster bezel away from the instrument panel far enough to access and disconnect the instrument panel wire harness connectors from the receptacles for the passenger airbag on/off switch (if equipped), the rear window defogger switch (if equipped), the heater-air conditioner control, and the transfer case switch (if equipped).ĩ. Pull the right side of the cluster bezel away from the instrument panel far enough to access and disconnect the instrument panel wire harness connector for the headlamp switch from the switch connector receptacle.Ĩ. Using a trim stick or another suitable wide flat-bladed tool, gently pry around the perimeter of the cluster bezel to disengage each of the snap clips from their receptacles in the instrument panel base trim.ħ. Remove the two screws in the hooded area above the instrument cluster that secure the cluster bezel to the instrument panel base trim (Fig. Remove the steering column opening cover from the instrument panel.ĥ. If the vehicle is equipped with a tilt column, set the tilt steering column in its lowest position.Ĥ. The front panel (face plate) does not pull open from the top like on some window AC's to get to the filter, but the filter slides in and out of a slot on the right side of the front panel. If the vehicle is equipped with an automatic transmission, turn the ignition switch to the Unlock position, set the park brake, and place the automatic transmission gear selector lever in the Low position.ģ. I have a model AET05LQW1 GE 5,000 btu window air conditioner with a 'slide in' filter and manual (not electronic) controls and thermostat. Perform the A/C cool down test using the DRB III.Ģ. Refer to: Instrument Panel, Gauges and Warning Indicators, Instrument Cluster Carrier, Service and Repair, Instrument Cluster Service Procedures, Instrument Cluster Bezel Replacement,ĥ. Reinstall the cluster bezel to the instrument panel. Position the heater- A/C control in the cluster bezel and secure it with four screws. Plug the wire harness connector into the back of the heater-A/C control.Ģ. Remove the heater-A/C control from the instrument panel.ġ. To solve, just imagine the following changes to the nomenclature on the push buttons on the panel: AC -> Compressor ON/OFF. Unplug the wire harness connector from the back of the heater-A/C controlĥ. I run into the same confusion with the auto climate panel on both our 500 Sport and 500e. Remove the four screws that secure the heater- A/C control to the cluster bezel.Ĥ. Refer to: Instrument Panel, Gauges and Warning Indicators, Instrument Cluster Carrier, Service and Repair, Instrument Cluster Service Procedures, Instrument Cluster Bezel Replacement,įig. Disconnect and isolate the battery negative cable.Ģ. I attached a procedure and a picture for you to view.ġ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |