You can scan at lower resolutions, but the results may not be good enough if you want to make prints or copy regions of the image later on. It’s been a while since I scanned slides, but I remember that a tray of 8 slides on my scanner took well over an hour to complete. Scanning a slide at 3600 dpi (which will produce an image of about 5040x3384 from a standard 35mm slide, and will print to 8.5x11 paper at about 400 dpi) may take several minutes per slide. The biggest problem with scanning slides on any flatbed scanner is that it takes a long time. It appears that VueScan also supports this via the Multi crop feature. This way you can set up as many slides as will fit on the glass, start a batch scan and go do something else while it runs (see below - high resolution scanning can take a long time). The software will scan each of those rectangles to a separate output file (or a separate document window if you’re scanning via the Photoshop plugin). With this, after you perform the preview scan, you can drag rectangles around multiple images (e.g. One feature I use a lot in SilverFast is batch scanning. There is a bit of a learning curve, but it’s not hard to figure out and it has very good support for scanning slides and negatives, including a database of popular film types for more precise color calibration. It has V600 support and has its own IR-based scratch removal system ( iSRD). It’s a bit more expensive, although the entry-level “ SE” version is not too expensive ($50), unless you need Kodachrome support, which is only in the “ SE Plus” version ($100). I personally use SilverFast for my scanning. Here’s the page for an Epson V600 and IR scanning is supported. You can check if it has support for your hardware on the scanner support page. But they do support scanning with the infrared lamp (using their own algorithm, which they claim is better than the ICE algorithm) in order to detect and remove dust. Well, to be pedantic, they don’t support that, because Digital ICE is a trademarked name/algorithm. EpsonScan works, but I don’t think it’s a very good app. At least that’s the case for my Perfection 4870 Photo scanner.ĭon’t bother with the included software. The only potential gotcha is that the holders have a notch in them toward the back of the holder, which you also need to cut out (the transparency projector shines through it for some self-calibration mode). Just cut slide-size holes in it so that they are under the transparency projector in the lid. You can make your own with a sheet of cardboard. They’re convenient, but they’re just a plastic frame for positioning slides. I do have VueScan but I don’t think that has ICE built in the way the Epson software does.įirst off, don’t worry about the slide holders. My question is - how is the software that comes with it? I am still running Sierra though I will be upgrading to HS when I get the time to do my ssd upgrade. So I’m looking at the Epson V600 (I love my old Epson Perfection flatbed, but I bought it refurbished and it didn’t come with the slide/negative holders). So go ahead, give it a try and let us know your thoughts.I have been using my Wolverine quite a bit, but definitely need better resolution for some of my negatives and slides. We’re excited to see how these enhancements transform your photo scanning process. This automatic cropping and straightening feature not only saves you time, but also simplifies the scanning process, eliminating the need for manual adjustments and allowing for simple rotation corrections. If you have JPEG selected as the file type, each image will be saved in it’s own JPEG file.Īnd there you have it! By following these simple steps, you can utilize the power of VueScan 9.8.06 to scan multiple photos on a flatbed. Press the Scan button to scan and save the images you previewed. You can adjust the rotation angle with the dot on the right hand side of the image. You can also draw a new box by clicking and dragging outside the bounds of a crop box. You can adjust the width and height with the handles on the sides of the image. You can delete a crop box by pressing the Delete key. VueScan should automatically recgonize each photo, but sometimes it will make a mistake. Press the Preview button and you’ll see your photos in the right hand Overview area. If you ever need to go back to the default settings you can select File | Default Options in the top menu bar. These options should be on by default, but make sure Input | Autoskew is turned on and Crop | Multi crop is turned on. Also, make sure the photos aren’t overlapping with each other. If they’re too close together then we can’t recognize them as separate items. Make sure you leave some space in between the photos. VueScan automatically cropping and rotating the 4 scanned photos
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |